From collectibles to cars, buy and sell all kinds of items on eBayWelcome! Sign in or register.
Site Map
aAdvanced Search
Popular products
No suggestions.
Hide eBay suggestions
BuySellMy eBayCommunityHelp
PTI Pavement Repair Products
PTI Pavement Repair Products
Maintained by:
davbfd ( 249)
PTI Pavement Repair Products is an Authorized Wholesale Distributor of the rapid cure pavement repair materials FLOMIX®, and FLEXSET®. These advanced high strength urethane polymer materials allow for simple, quick, and cost-effective repair and restoration of Concrete or Asphalt US DOT Approved.
FLOMIX Asphalt and FLEXSET Concrete
Who is Using Our Products
Video Demonstration
Application Instructions and FAQ
Picture Gallery
About the seller

Please pardon our dust while we imporve our storefront to better serve our customers.

You may notice that MOST OF OUR IMAGES AND PICTURES ARE NOT APPEARING.
We are workng to resolve this issue. Thank you for your patience.

If you have questions, our Customer Support Department can be reached at 281-778-3223.

Store search
in titles & description
Store categories
Store home

            
     Add to Google 
     
     Subscribe in NewsGator Online


            FloMix®
 2002 Top New Products
          of the Year

      Official PayPal Seal

Store Map
  

APPLICATION INSTRUCTIONS

   FloFlex5200

SURFACE PREPARATION

Clean out with a brush or blow out any cracks or potholes with a leaf blower or compressed air to remove loose and unsound material.

Apply to dry surfaces only. Moist or damp surfaces will weaken products ability to bond to the surface. KEEP PAILS SEALED UNTIL READY FOR USE

MIXING

Remove 10-pound bag of topping sand and both A & B bottles of polymer from the 5-gallon pail. Shake the A & B bottles to mix well before use. Add the "A" bottle of polymer to the 5 gallon container of treated sand and mix with a pail mixer for 1 to 2 minutes until sand is completely wet. Next, add all of "B" polymer and mix thoroughly for 1 to 3 minutes. A longer mix of the "B" component will accelerate the cure time slightly and insures proper mixing. The material is now ready to be applied to the prepared area and should be in the form of a very pourable slurry. Working time will be approximately 9-12 minutes at an ambient temperature of 75 degrees F.

INSTALLATION

Squeegee, screed, gauge-rake or trowel the thin slurry over the repair area. The outer areas of the repair can be feathered into the existing surface with a hand trowel. Once the liquid material is applied to the repair area, broadcast the repair using all 10 pounds of the included topping sand evenly over the repair area. Apply the topping sand in several passes as the material begins to cure.

CURE

Cure for one hour minimum at a temperature of 75 degrees F. allowing approximately 30 minutes for every 5 degrees below 75 degrees. To maintain a rapid cure at lower temperatures, add a measured amount of the supplied (free upon request) catalyst per the included intructions (see the FAQ below). Colder temperatures will dictate a slower cure rate.

PACKAGING & COVERAGE

FlexSet and FloMix: 5-Gallon Kit 55 lbs.
5-gallon kits will cover approximately 50 square feet @ 1/8" depth.

SHELF LIFE

One year when stored indoors, unopened under cool and dry conditions.

PAIL DISPOSAL

Dispose empty pails in accordance with local, state and federal regulations.

FIRST AID IF INHALED

Remove to fresh air, if not breathing, give artificial respiration, preferably mouth to mouth. If breathing is difficult, give oxygen, call a physician.

SKIN CONTACT

Wash skin with soap and water. Remove contaminated clothing.

EYE CONTACT

Flush with water; continue for at least 15 minutes. Contact a physician.

SPILL OR LEAK

In case of liquid spill of unmixed materials A&B absorb spilled material with sawdust, sand or other absorbent, sweep into waste container, neutralize with decontamination solution (93% water, 5% ammonia, 2% detergent) and store open container outdoors for a minimum of 24 hours. Dispose neutralized waste in accordance with Federal, State and local government environmental regulations.

DEEP POTHOLE REPAIR
  • Blow out standing water with a leaf blower or compressed air. Allow to dry, or dry wet asphalt or concrete with a propane torch. Area MUST be dry to ensure maximum performance.
  • Place ¾" crushed, clean, dry angular (not river rock) aggregate evenly just below grade. Combine A bottle of polymer with sand mixture and blend. Mix to wet out sand completely, than add B bottle of polymer and mix 1 to 3 minutes.
  • Pour mixture evenly over aggregate allowing penetration to bottom of repair. Material can be spread using a squeegee, gauge rake or trowel.
  • When product is level to grade, broadcast topping sand evenly over surface. The high traction surface matches the surrounding asphalt or concrete in appearance and can be returned to traffic in about 60 minutes. 

 

FREQUENTLY ASKED QUESTIONS


Q: How do I maintain a rapid cure when it is cold?
A: Use an appropriate amount of the included catalyst

Directions for use of catalyst with FloMix and FlexSet (optional)

Cure FLOMIX or FLEXSET for one hour minimum at a temperature of 75 degrees F. allowing approximately 30 minutes for every 5 degrees below 75 degrees.

MIXING of the ”B” Polymer component for 1 or 2 extra minutes is the first step to take to increase the cure rate at slightly cooler temperatures, or anytime you are looking for a little added speed.

To maintain a rapid cure at lower temperatures below 75 degrees add a measured portion of the vial of the supplied catalyst (2 oz.) appropriate to your conditions. Add the catalyst to the “B” component and shake before adding the “B” to the treated sand. Catalyst is free upon request with your order.

You will need to experiment to find what works best for your climate and project at hand. The following are approximate suggestions.

For temperatures below 70 degrees add 1/4 of the bottle of catalyst or less
For temperatures below 60 degrees add ½ of the bottle of catalyst or less
For temperatures below 50 degrees add ¾ of the bottle of catalyst or less
For temperatures below 40 degrees add the entire bottle of catalyst or less

Colder temperatures will dictate a slower cure rate.

 

Q:  Where can I find the MSDS sheets for this product?

A:  The MSDS sheets are available in Adobe Portable Document format (.pdf)

FlexSet A-side MSDS.pdf
FlexSet B-side MSDS.pdf
FlowMix A-side MSDS.pdf
FlowMix B-side MSDS.pdf

 

 

Q:  How can I calculate repair area sq. Ft. coverage with your products?

A:  Coverage calculation will depend upon the type of installation you need to perform. The material label reads:

 

“Each 5-gallon kit (55 pounds) will cover 50 square feet @ 1/8” depth”

 

This coverage rate applies to surface repairs such as restoring alligatored asphalt, or any skim application, such as to cure a pavement bird bath (puddle), surface fracturing, pitting, or floor restoration. In my experience with the product, I have found that 40 to 50 square feet per kit is accurate depending on the average depth of the pavement degradation

 

When using the product for deep pothole, spall, or large crack repairs, you can expect each 5-gal kit to fill approximately 1 cubic foot. Use the material over a ¾” clean dry angular aggregate. This will extend the cubic volume of coverage, as well as add additional compressive strength to the repair.

 

 

Q:  Is this product tested and approved by any government or industry agency?

A:  Yes, FloMix® and FlexSet® are approved by Department of Transportation Material Labs and Maintenance Departments for our U.S. airports, highways, bridges and roads; we provide a long-term, load-bearing, rapid repair solution for all your concrete and asphalt restoration needs. NATO/USAF APPROVED for rapid runway repairs.

 

 

Q:  What tools will I need to install this material?

A: We suggest you have the following items available:

  • Broom or leaf blower (or air compressor)
  • Drill - any quality 3/8" drill
  • Egg-Beater style Pail Mixer - or similiar non-aerating mixer. Used to mix the material


  • Trowel or squeegee
  • Eye protection and gloves
  • Rags or towels for cleanup

 

The following items are not necessary, but may be helpful

  • Duct or Masking Tape - If you wish to "form" your patch to a limited area with sharp clean lines
  • Propane torch - Only if it is necessary to dry out your area of repair.

 

Q: How much is shipping for a single 5-Gal kit?

A: We use FedEx Ground for orders of 11 kits or less. FedEx is currently the lowest cost method. We will determine and use the lowest possible cost method for every order. See the listing for your Calculated Shipping cost. Orders of 12 or more kits may be shipped by freight and will be determined by point to point lowest cost. We do not profit from shipping or freight.

Q: What FedEx Zone am I?
A: You can view your FedEx Zone here: FedEx Zone Locator.pdf

Please inform us whenever your "deliver to" location is a Business Address, and please include your telephone number for the FedEx documentation.

 

FREIGHT: Orders of between 12 and 17 Kits may be delivered by common Freight Carrier if lowest cost. All orders of 18 Kits (half palette) or more are shipped directly from the factory by common Freight Carrier at prevailing rates and discounts. We do not profit from or pad freight.

 

FedEx Delivery time - Days

 

Q: Are FLOMIX and FLEXSET repairs environmentally safe?
A: Repairs are environmentally safe because NO toxic wastes are generated. With no pavement removal no waste asphalt is generated.

 

 

Q: Are FLOMIX and FLEXSET repairs waterproof or chemically resistant?

A: FloMix seals, waterproofs and fuel-proofs asphalt. FlexSet seals, waterproofs and fuel-proofs concrete. The materials are unaffected by dilute acids and bases, gasoline, diesel, aviation fuel, antifreeze, or lubricating oils and is insoluble in most solvents and chemicals.

 

 

Q: Are FLOMIX or FLEXSET repairs slippery?

A: The sand topping placed over FloMix and FlexSet creates a high traction surface with a high coefficient of friction whether wet or dry.

 

 

Q: Do FLOMIX and FLEXSET repairs hold up to snow plows?

A: Snow plows will not damage properly applied, flush to grade FloMix or FlexSet repairs.

 

 

Q: Does FLOMIX stop water erosion of asphalt?

A: Asphalt deteriorates quickly with repetitive water runoff found at car washes, outside restaurant kitchens, and with landscape irrigation. Water damage to asphalt is stopped when asphalt is resurfaced with FloMix.

 

 

Q: Can FLOMIX and FLEXSET be used on large areas subjected to chemical spills?

A: Resurfacing asphalt with FloMix, or concrete with FlexSet, protects surfaces from cooking oil, oil dripping from cars, fuel, chemical, and toxic waste spillage. Fuel storage & toxic waste sites, secondary containment, service stations, fast food restaurants, airport runways & aprons, parking lots and parking structures are typical installations that benefit from resurfacing with FloMix or FlexSet.

 

 

Q: Can all asphalt damage be repaired successfully with FLOMIX?

A: No. With severe base damage, asphalt repairs with FloMix are not durable. FloMix repairs are not recommended over asphalt base that is structurally inadequate.

 

 

Q: Can FLOMIX repairs be used before placing asphalt overlays?

A: FloMix will repair wide cracks, raveling, and alligatoring in asphalt prior to overlaying, chip sealing, slurrying, or seal coating. FloMix can provide substantial savings compared to conventional labor intensive grinding and dig-outs normally associated with hot mix repairs. Load bearing FloMix repair stops reflective cracks for asphalt overlays.

 

 

Q: Are FLOMIX or FLEXSET repairs affected by hot asphalt overlays?

A: FloMix and FlexSet repairs are NOT affected by hot asphalt overlays. There is no softening and no melting. Asphalt overlays, chip and slurry seals and micro-paving bond to FloMix and FlexSet repairs.

 

 

Q:  I have repaired my pavement with FlexSet or FloMix, how soon can I seal coat or paint stripe?

A:  Repairs can be seal coated or striped / painted one hour after completing the repairs.

 

 

Summary of My Selling Policies
Payment Winning bidders are asked to contact us within two business days. We prefer payment by credit card via our own merchant account, or by company check with an approved account. We do accept PayPal, cashier check, money orders and other mutually agreed upon methods upon approval by PTI.
Fees Sales Tax is charged only within the State of Texas 8.25%. No handling fees are charged by PTI on shipping or palette quantity freight charges.
Shipping Normal freight or shipping charges apply to all orders and are paid by Buyer. We always ship at the lowest possible cost except at buyers request for specific method, shipper or freight line. We will ship to Worldwide. We do not profit from freight.
Delivery Items are released to the shipping department for dispatch immediately upon clearance of payment. Most orders are shipped within 1 to 3 days. Due to manufacturing and production schedules and varying product demand, possible short term backorders can occur. We strive to keep our customers informed on the status of their order.
Refunds & Returns Refunds are offered if a customer is not satisfied. Returned material must be in sealed and merchantable condition. Requests for refund must be made within 30 days of receipt of the order. Returns will not be accepted without prior written authorization from PTI. Buyer is responsible for all freight or shipping charges associated with the return.
Contact Me We may be contacted the following ways: David Jennings 281-778-3223. roaddoctor@earthlink.net. Emails are typically returned within 1 hour during normal business hours. Business Hours: 8am to 8pm central time zone.
BID WITH CONFIDENCE
 
 
 
Visit the All Repair Materials,  FlexSet Concrete® or FloMix Asphalt® link to view our complete listing of available items for sale, and all current promotions.
 
 

We appreciate your interest in our products and would like to answer any additional questions you may have. You are welcome to contact us thru the eBay messaging system, or directly at roaddoctor@earthlink.net with your inquiry.

Add Me to Your Favorite Stores!

FloFlex1thumb


An eBay Store maintained by:
davbfd ( 249)
Seller, manage Store
Tools:My eBay
 Learn more about feeds

About eBay | Announcements | Security Center | Resolution Center | eBay Toolbar | Policies | Government Relations | Site Map | Help
Copyright © 1995-2009 eBay Inc. All Rights Reserved. Designated trademarks and brands are the property of their respective owners. Use of this Web site constitutes acceptance of the eBay User Agreement and Privacy Policy.
eBay official time